|
| |
|
|
|
|
|
|
|
Liquid Laminators |
 |
| |
|
|
|
|
|
|
| |
Great for protecting wide format prints |
 |
|
| |
|
• Outdoor signage (vinyls, scrim banner etc)
• Fine art prints (water resistant canvas)
• Vehicle and boat graphics (vinyls)
(note: not designed for photographic
media or bond papers).
EZ Glide Applicator
• Applies a precise coating that’s
always smooth and even.
• Saves money by eliminating spray
waste and heavy, streaky finishes
from hand brushing.
• Much faster than spraying, brushing.
• Costs less than other coaters and
faster than motorized coaters.
• Easy to use and easy to clean.
• Available in 27”, 48”, 55” and 62” widths
|
|
|
 |
| |
|
|
Rollaguard Coatings
• Costs significantly less per
application than film laminates.
• Provides excellent UV, abrasion
and water protection.
• Enhances the vibrancy of the inks.
• Media retains its flexibility.
• Will not crack or peel off
|
|
|
|
| |
|
|
 |
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
Takes only a minute to set up, seconds to coat and 10 minutes to clean. |
| |
|
|
|
 |
| |
|
|
|
|
|
|
Here is how it works:
1.
Two braces are inserted
into the back of the
EZ Glide. |
 |
 |
| |
|
|
|
2.
The braces then hook onto
the end of the table to
secure the applicator,
making it easily adaptable
to any size table. |
|
 |
| |
|
|
3.
Pour the coating into the
back of the tray.
|
|
 |
| |
|
|
4.
Swivel up the coating rod
and place your print over
the tray, with the first two
inches extended over the
front of the tray.
|
|
 |
| |
|
|
5.
Swivel down the coating
rod and the first two inches
of the print will be submerged
in the coating. . .
|
|
 |
| |
|
|
.
. . .while the front of the print
is captured between the
coating rod on top and the
silicone squeegee on the
bottom. Note: this is a special
wire wound coating rod that
is used in many applications
where a precision coating
is required.
|
|
 |
| |
|
|
6.
Pull the print through the
applicator. The print slides
through very easily. As it goes
through, the coating rod wipes
off the excess coating leaving
a perfectly smooth coating.
The red squeegee wipes the
back of the print completely
clean (so it will not effect the
adhesive on pressure
sensitive vinyls.)
|
|
 |
| |
|
|
7.
When finished coating for
the day, loosen three screws
and the top half with the
coating rod comes off easily.
Cleans with water.
|
|
 |
| |
|
|
8. Use the tube to drain the
coating back into the bottle
(takes about 2 ½ minutes
to drain). Then wash out
the tray. |
|
 |
| |
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
Specifications |
 |
 |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
Coating Widths |
|
27", 48", 55" and 62" |
Coating Thickness |
|
1/2 mil (dry) |
Cost |
|
11 cents per square foot |
| Dry time |
|
15 to 25 minutes depending on humidity and media type |
| Finishes |
|
gloss or satin |
Coverage |
|
650 square feet per gallon |
|
|
|
|
| |
|
 |
 |
|
 |